Tuning...Tuning... Tuning...

[PCPeteUK]

Hi Winston - how/where have you mounted the suction cup?
I currently have this on the side beneath the mirror - with a lanyard tied to the mirror just in case - but I find the film quality very jerky as it seems to bounce a lot.
Sorry for deviating from the thread.

[MGvalerio]

If you do not want to vibrations of the image, the cup should be amended so.



MGvalerio.

[PCPeteUK]

Many thanks MGvalerio - how do you ensure the suction cup (and GoPro) isn't lost if it falls off?

Molti MGvalerio grazie - come si fa a garantire la ventosa (e GoPro) non si perde se si cade?

[O.C.]

Pete. I use a neck lanyard tied to the mirror.. The suction cup is very strong and shouldn't come unstuck.

[MGvalerio]

x PCPeteUK

Pete. I use a neck lanyard tied to the mirror.. The suction cup is very strong and shouldn't come unstuck.

It is very easy ... with wire line to the suction cup and the first 10 cm of the screw holder
Front cover of the bike.


MGvalerio.

[virginiajim]

Little things that make a great bike.

"http://www.youtube.com/embed/ByocBFzi9xk"


MGvalerio.

So MG, not content to graze in one pasture?  You really can't hide.  You know that don't you?   And you have a higher post count here to top it all off.

[MGvalerio]

  virginiajim 
Ciao Boss 

MGvalerio

[virginiajim]

 

[PCPeteUK]

Hi MG - your post on YouTube - http://www.youtube.com/watch?v=07WfuKCrgVw&lc=v78tVXhcmOP9vlMUWauMkcpN3e7lXhCOM_DNZqioV-M&feature=em-comment_reply_received&lch=email_reply
seems to show a GoPro mount on the outside end of the bar end - any chance you could let me/us know where this was sourced from?

I think I prefer the mounting to the outside as you show in your clip above to the inside - although I have a RAM mount fitted inside the clutch end just in case. I have also fitted a permanent centre mount under the screen as you have. this works quite well although I have been unable to cure the motion vibration.

As always your video's are very informative and seem to provoke more questions 

[MGvalerio]

Supports for the GoPro are original but adapted to my needs for video recording.

http://youtu.be/pUxL82znvk8


MGvalerio.

[PCPeteUK]

Hi MG - I have to admit defeat, you are too clever for me. Even after watching the video I still cannot work out how you have managed to get the mount point into the hexagonal recess for the bolt 

I am guessing it is araldite or something similar. Or have you tapped a thread into the recess to take the bar? Either way it is very ingenious. Well done...

I'm sure you could make a lucrative second income with all these adaptions you undertake on your GTR.

Ciao MG - Devo ammettere la sconfitta, sei troppo intelligente per me. Anche dopo aver visto il video non riesco ancora a capire come siete riusciti a ottenere il punto di montaggio nella cavità esagonale del bullone: smiley:

Sto indovinando che è araldite o qualcosa di simile. O hai toccato un filo nella cavità di prendere il bar? In entrambi i casi è molto ingegnoso. Ben fatto ...

Sono sicuro che si potrebbe fare un reddito lucrativo secondo con tutti questi adattamenti si impegnano sul GTR.

[MGvalerio]

Even after watching the video I still cannot work out how you have managed to get the mount point into the hexagonal recess for the bolt 

Molto più semplice amico GTRista ...Fatta filettatura di 8mm.nella vite del fermo manubrio accelleratore.
Much more than just a friend GTRista: smiley: ... Without thread 10mm.nella handlebar throttle stop screw.
MGvalerio.

[PCPeteUK]

aaah!! understand now - many thanks MG. Time to ask a friend to drill and tap a thread for me 

[MGvalerio]

aaah!! understand now - many thanks MG. Time to ask a friend to drill and tap a thread for me 

There are scenes that I could not cut, however, the video is instructive.

http://youtu.be/KFTklAWwlv8?t=16s

MGvalerio.

[PCPeteUK]

Many thanks MG.....makes everything clear