pillion footpegs

[viper]

I take it that the 12mm spacer went in ok with any feckling.

I did away with the spring and pin, used a 6mm stainless bolt and nut and just tensioned it up so the pegs were a movable put tight fit up and down.

[O.C.]

I take it that the 12mm spacer went in ok with any feckling.

I did away with the spring and pin, used a 6mm stainless bolt and nut and just tensioned it up so the pegs were a movable put tight fit up and down.

the spacer went in just fine, and only a small amount of persuasion was needed toi line it all up

I did consider drilling the peg to accomodate the spring/ball retract, but their isn't enough material in the new pegs to allow for drilling out

The new pegs are a massive improvement over the old 'standard' ones ...thanks for the tip and also the 12mm/6mm shims which fit perfectly

a pint is owed or whatever other tipple is your choice    

[Lonewolf]

Not sure how accurate this is but an MOT tester once told me that if the pegs wont retract then that's a fail, again, not sure whether this was bull  , (see what I did there)    or the truth, surely an MOT tester wouldn't lie, they're all    aren't they?

[O.C.]

Not sure how accurate this is but an MOT tester once told me that if the pegs wont retract then that's a fail, again, not sure whether this was bull  , (see what I did there)    or the truth, surely an MOT tester wouldn't lie, they're all    aren't they?

Ermmm. Steve, Within my post I actually I did say that they "will recoil"..... its just that they don't stay upright on their own, the bolt method that Viper used is one way round this 

Its  a simple fix.. when I work it out....maybe a postmans Red rubber band would do the job   

[Lonewolf]

My apologies, I didn't take that bit in.

[100milesaway]

My apologies, I didn't take that bit in.

No because you were too busy talking 

[Lonewolf]

  No because you were too busy talking 

  I think I'd previously been given some duff info from a tester. I stand corrected.

[MGvalerio]

Si può fare meglio ..credo...Mia produzione .. Prolungo Pedane Postereiori .http://youtu.be/9yr-Dvvwuc8

MGvalerio

[O.C.]

Su vinculación producción de la reducción entre paréntesis son excelentes.

Supongo que están diseñados para funcionar con el sistema de escape de serie en el que habrá espacio suficiente para que bajen totalmente

El problema que yo y otros tenemos es que los kits de bajas, no funciona cuando un sistema de escape del mercado de accesorios está equipado

[MGvalerio]

olde coney ... osserva bene le mie prolunghe pedane,non sono come Aftermarket,sono di forma curva per allontanare in avanti  la pedana ,non problemi con mie prolungo pedane x passeggero.

Posterò un filmato in giornata.

MGvalerio.

[MGvalerio]

Video delle prolungo pedane passeggero.


http://youtu.be/XaCCCMCzeAs


MGvalerio.

[viper]

just watched his video and on my 2010 model , his is 2008 , my stock exhaust collar is much closer to the original bracket than his. I have peg lowers and they are a nats dick away from the exhaust

[O.C.]

olde coney ... osserva bene le mie prolunghe pedane,non sono come Aftermarket,sono di forma curva per allontanare in avanti  la pedana ,non problemi con mie prolungo pedane x passeggero.

Posterò un filmato in giornata.

MGvalerio.

Gracias.

Le pregunté a necause Sé que esto puede ser un problema con algunos paridad del mercado de accesorios de otros soportes de la reducción

[MGvalerio]

http://youtu.be/Ldq1-WrGgWc

Some accessories, per passenger, per trunk, changed the main stand, I have set a parking brake, all my work.
MGvalero.