hi guys,
looking for some help and advise please?,cuz i know you guys got it!,
well, santa`s brought me some heated grips-they are symtec,the one with a heated element that fits under the grips (just like a silver foil element,bought um off ebay,oops i meen santa did!) lol.
anyway,when i was looking into this,couldnt be doing with the oxford type with a huge square control box stuck on the bars/bike. My mate had a set of these on his track bike an said they were brill,so got these with a nice neat rocker switch which im gonna fit to the fairing panel.
Few people has said that if i wire um to the battery an i forget to turn um off,or even some knob head decides to turn them on when parked id be fooked with a flat battery!,,,,,,,,,so,,,,,,, is there a accessory fuse or possibly a lighting wire i can connect these to instead of the direct route to the battery??- only thinking this as it will only be possible to turn on when the ignition is on? am i right in thinking this way or not???
Was going to have a look at fitting these today but thought fook that! it was to cold in the garage today!,,,,,,,,,,,,,, thanks for reading guys an look forward to hearin g from you all, hope you all have a fab new year,take it easy on the booze guys!!!
reguards the jenros family! :)
There is an ignition fed 12v supply under the nearside fairing.
hi patrick,
near side!- u meen l/h sade sat on the bike??
can u give me a bit more info on tha please, not much idea on the leads,havent taken anything off the bike at the moment to see whats where n tha, thanks anyway ;)
yes left side when sitting on the bike.
I had my heated grips fitted by the dealer when i bought my bike (2009 model) but i told him about the power feed and he used it.
I'm sure that someone who knows better than me will be along shortly but i thinks the feed is tucked inside a wide black sheath and very easy to get at.
thanks pat i will have a look tomorrow if it aint to cold!lol
jenros, the connector is inside the black plastic shroud which you can see on the below photograph.
(http://i151.photobucket.com/albums/s139/Jaffa_Cake101/Fingers/100_0883.jpg)
thanks very much lone wolf, big help there! ;)
Told you someone knowing more than me would arrive shortly!
P
Everything I've ever learnt about the GTR I've either learnt from Kwikasfuki or from dismantling the bike. ;D
well thats what i love about you guys,,,,,helpful is a understatment!!!!!!!! .
Happy new year to you all,,,,im off out for a jar now,not to many thou,,,,,,,dirt bikes calling in the morning!!!!!!!!!!! happy days, yeeeeeeeeee haaaaaaaaa :)
hi mate,well today decided to have a go at fitting my heated grips!(at last,just been to cold to be messing about in the garage),you said to take off the cover above the fairing (l/h side) did this but cant get the bloody popper button off,which is holding the top part of the cover on.
when i fitted the leds to the front i wired the leds from underside the panel at the front,managed to get my finger about these poppers to free um an take them out,but this bugger is right behind the windscreen riser,(i have a large aftermarket screen fitted to mine an looks like there is a sticky foam washer behind the screen an i think im gonna bugger the gasket up if i remove it?
what is the best way to get this released,or do i just damage the popper an replace it with a new one???,
theres prob a tool available to remove these,yeah?
lastly,,,lol- what colour is the live wire,know this sounds daft but,on my wiring diagram for the heated grips the white is live,an the red is earth!!!!!,,,bloody mental!!!!!!
thanks guys,but went out for a blast on a nice morning last week an my fingers were numb with the cold,so on they gorro go!!!.
cheers guys,an looks like spring is well on the go!!! about time too.
forgot to say as well,where the plastic shroud is my power commander is zip tied to this shroud,an its as tight as a cods arse!!!,,,,,,,,,at 40 fathoms of course,lol
jenros, fear not. :mfr_lol:
Firstly the little popper behind the screen is tricky to get to but you have to understand how they work. You can take the screen off if you wish and that will make the job significantly easier but you do not have to. The gasket on the screen behind the black plastic bracket is made of rubber/neoprene or similar, you wont damage it if you do decide to remove the screen. Be mindful though that the black plastic brackets are only made of PLASTIC, ifyou over tighten the four bolts holding this piece of trim in place they will develop tiny stress cracks, just tighten them ever so gently if you decide to remove the screen.
I've found the easiest way to remove the popper behind the screen is to use a small Allen key and use the short end to pop the pusher in. Yes that's right in order to remove the popper you push the middle part of the popper in this will then allow you to get your nail or something very thin under one edge and it will just lift out. When reversing this procedure the centre part of the pin will be protuding quite a way out, you simply push it down until it is flush with the head of the pin, after you have placed the pin in the hole. It''ll all make sense when you get it out, just have a play with it and see how it works.
As for the wires, on the bike, black + yellow is NEGATIVE and black is POSITIVE.
Hope that helps to some degree.
What's the correct name for these 'poppers'? I need to get some
Quote from: Kwikasfuki on March 07, 2012, 09:36:44 AM
What's the correct name for these 'poppers'? I need to get some
I dont know what they are specifically called but I have some spare ones, they are not a part which needs ordering in specially, any decent Kwak dealership will have them as they are as I understand it standard amongst the Kwak range. They only cost a few pence.
I've always called them plastic rivets or plastic push fasteners. If you use either term on ebay, you end up with hundreds to choose from.
I just think you have to measure the length and diameter to get the correct size, then decide on the style and colour.
I think Halfords suppy them too, but a lot more expensive than ebay.
thanks lone wolf :clap:,thought there was prob an easier way,cheers mate im gonna have a look now
KWIKASFUKI, the name of the popers are,(as ive now named um)=these,effing ,poxy,things!!!!!, so if you ring up ya local kwak shop to order some just ask for these,,,,,,an tell um ive told you to ring,they will knowexactly wha you want :mfr_lol: :mfr_lol: :mfr_lol:
Quote from: shaggs147 on March 07, 2012, 06:55:26 PM
I've always called them plastic rivets or plastic push fasteners. If you use either term on ebay, you end up with hundreds to choose from.
I just think you have to measure the length and diameter to get the correct size, then decide on the style and colour.
I think Halfords suppy them too, but a lot more expensive than ebay.
Thanks for that. Ordered those and some well nuts.
thanks guys,had a go at getting the popper out,,,,,,,,,,,,about 15 seconds!,brill!,,,,found the live wire that you said lone wolf,,,,,,big thanks for everyone who replyed :clap:,,,gonna have a go prob friday evening to connect everything back togeather,i will let you know how they perform,an hopefully,,,bit of fine weather on the weekend i will give um a blast an see how they perform,if the weathers not to good,we are off lane clearing an cutting back some trees and crap around the trails that we use in our area,,(for those that are reading this an thinking,durrrrr!,im talking dirt bikes),,,so im onto a winner rain or shine! :clap:
YEEEEEEEEE HAAAAAAAAAA :clap:, grips fitted and working!!!, just wants some fine weather for sunday to try them out.
Many thanks for all your help,especially LONEWOLF!!! :clap:,without your pics of tha wiring shroud i would have been knackered,so if we meet up some time,,,,,,,,,a beer or two shall be put your way mate, :wink:, thanks very much,an i will let you know how they perform.
Glad it worked out for you. The GTR is really a pretty easy bike to work on.
worked a treat :clap:
What a happy forum this is !! :mfr_lol: :mfr_lol: I love it here !
Quote from: Rusty on March 12, 2012, 08:40:53 PM
What a happy forum this is !! :mfr_lol: :mfr_lol: I love it here !
:agree:
:agree: :agree: me to! lol