Rear Peg Replacement

[PCPeteUK]

Advise time please you guru's of everything GTR - what rear pegs can I buy to replace the cast alloy ones - Mrs Pete stipulates they MUST have a rubber top.
Over to the floor.....

[O.C.]

ER6(F) a I think its (F) but maybe (N), also I think ZZR, but all Kawasaki gen parts will be pricey, so check fleabay for breakers parts 

Its also possible to buy lowering kit including rubber top pegs which come from an FJR 

[PCPeteUK]

Many thanks OC - can find a pair of ER6N's from the states but a bit pricey and there is 1 FJR peg. Will add to my saved searches and see what turns up on flea bay over the next few weeks....

[O.C.]

I can't remember which way round it is ER6 N (naked) or ER6 F (Faired) but one has rubber pegs and the other doesn't

[Bryn]

I've got FJR 1300 rear pegs on mine. Fit very well

[Boomer]

Mine has GTR1000 pegs. Not pretty but SWMBO likes them.

[Charlie747]

Not pretty but SWMBO likes them.

If so all must be good...........................its a brave man who upsets the "Mama"

[dokterdave]

You want Kawasaki part numbers

34028B               Original Kawasaki Parts STEP,RR,RH Kawasaki Part Number: 340280315
34028C               Original Kawasaki Parts STEP,RR,LH Kawasaki Part Number: 340280314
34028D (two of) Original Kawasaki Parts STEP,FR,RUBBER Kawasaki Part Number: 340281430

92009 (4 of)        Original Kawasaki Parts SCREW Kawasaki Part Number: 920091404

Bit pricey tho at £118.64

Just swap your other bits over. They are a straight fit.
The GTR pegs have 1 detent spring and ball per side, the ER6 has 2
you only need 1

[Bryn]

Pretty FJR pegs   

[PCPeteUK]

Thanks Guys,
I will hang out for a 2nd hand pair of FJR or ER6N pegs on fleabay.... certainly don't want to pay full Kawasaki prices 

[O.C.]

Thanks Guys,
I will hang out for a 2nd hand pair of FJR or ER6N pegs on fleabay.... certainly don't want to pay full Kawasaki prices 

Try here Pete, just type you requirement into the search box and click 

http://www.dkmotorcycles.com/used-spares/

[PCPeteUK]

I've got FJR 1300 rear pegs on mine. Fit very well

Hi Mate just fitted the FJR replacements but I can't stop them bending lower under pressure (ie when pillion gets on) any suggestions?

Pictures here...
https://www.dropbox.com/sc/li4qxicrcrfsx0g/vHsAwA6Rd7

....I can't see any reason for them not working 

[O.C.]

Isn't there supposed to be a plate spacer behind them ?

[PCPeteUK]

Isn't there supposed to be a plate spacer behind them ?

I've used the original plus the one that came with the FJR peg to ensure a tight fit. So the peg is currently sandwiched between the two plates.

Both pegs look the same but when I put back the originals all is fine again !?! Baffled I is....

[O.C.]

Pete I'm guessing that the original is slightly larger than your replacement items, as I can't otherwise see why it doesnt fit.

From the pictures it appears that the replacement peg is not fitting snugly against the back of the bracket...is there a space between the back of the peg and the bracket on the bikes frame when the peg is in the down position ?  if so that's why the replacement pegs are drooping/straining under load, in which case you may need either a different replacement peg of some kind of spacer behind the peg mounting